Different grades of lubricating oil should not be mixed. Mixing oils of different qualities and grades will reduce the performance of the oil and produce viscous deposits and varnish-like precipitates, clogging the oil supply system and affecting the oil delivery. Under normal circumstances, the oil in the oil cooler, oil-gas separator, and oil circuit system should be replaced every 2000 hours, and the filter should be replaced or cleaned at the same time.
If operating in a high-dust or high-humidity environment, the oil change interval should be shortened. Currently, lubricating oil is generally subjected to regular sampling analysis, and the decision of whether to change the oil is made based on the sampling results.
Factors affecting the service life of oil include:
1. The inhaled air contains dust, iron oxide, carbon dioxide, and other substances that can accelerate oil deterioration;
2. Incomplete discharge of used oil will shorten the service life of newly added oil;
3. High compressor operating temperature can accelerate oil oxidation and deterioration;
4. Water leaking from the oil cooler enters the oil.
Rational and safe application of compressor lubricating oil
The basic task of compressor lubrication is to allow the lubricating oil to form a liquid layer (oil film) between relatively frictional surfaces to reduce wear and reduce power consumption on the frictional surfaces. It also cools the moving parts' frictional surfaces and seals the compressed gas working volume. At the same time, the lubricating oil also has secondary functions such as noise absorption, cleaning, rust prevention, corrosion prevention, and shock absorption.
The selection of compressor oil depends on factors such as the compressor structure, the composition of the compressed gas, the exhaust temperature, and the exhaust pressure. As shown in Table 1, the exhaust temperatures of different types of compressors also vary.
Correct selection of lubricating oil
According to the analysis of the causes of compressor fires and explosions, the most dangerous factor is the spontaneous combustion of oil carbon deposits. Part of the lubricating oil in the air compressor forms an oil film on the inner surface of the cylinder, while other lubricating oil molecules are suspended in the cylinder piston end face, piston ring groove, exhaust pipe, valve, air tank, and separator. Under the action of hot air, they oxidize to form carbonaceous substances. As these carbonaceous substances accumulate, they become carbon deposits, which are flammable. Oil carbon deposits can not only promote the spontaneous combustion of flammable mixtures but also cause oil to evaporate from the deposits, continuously forming flammable hydrocarbon mixtures. Therefore, compressed air containing both gas and liquid lubricating oil has the conditions for explosion.
The dynamic characteristics of lubricating oil in the compressor cylinders and pipelines largely depend on the quality of the lubricating oil. Therefore, the correct selection of lubricating oil is of great significance to the normal operation of the compressor.
It is wrong to blindly pursue lubricating oils with high flash points because the flash point and autoignition temperature are not related. The temperature of compressed air usually does not exceed 180-200℃. Under such conditions, lubricating oil vapor or carbon deposits may not necessarily spontaneously ignite. The flash point depends on the oil vapor pressure that poses an explosion hazard, i.e., the physical properties of the fuel; the ignition and autoignition temperature of the fuel depends on its thermal stability. For hydrocarbons with the same chemical structure, the boiling point of complex molecular substances is higher than that of simple molecular substances, and the vapor pressure of the former is lower than that of the latter, or the flash point of the former is higher than that of the latter. However, with the increasing complexity of the molecular structure, both its thermal stability and autoignition temperature decrease.
Lubricating oils with high flash points tend to produce more carbon deposits, while those with lower flash points not only produce less carbon deposits but are also more stable. In cases where it is difficult to predict the dynamic characteristics of lubrication in a compressor and the formation of carbon deposits under certain process conditions, special attention should be paid to minimizing the carbon deposit layer. Therefore, lubricating oils with excessively high flash points should not be used.
Based on research on the oxidation rate and chemical composition of oils, naphthenic oils produce less carbon deposits than commonly used paraffinic oils. To slow down the oxidation process and reduce carbon deposits, adding antioxidants to compressor oils is effective. Commonly used antioxidants include phenolic compounds and aromatic amine organic sulfides.
From the perspective of the formation of oil carbon deposits, the most essential characteristics of compressor lubricating oil are its evaporation performance and viscosity, which are related to the distillation fraction. Good lubricating oil should not contain a wide distillation fraction with low and high viscosity but should be a homogeneous narrow distillation fraction. Because the thermal effect in the cylinder is very strong, it is hoped that the lubricating oil injected into the cylinder will complete the lubrication of the frictional surfaces of the cylinder instantly and then quickly leave the cylinder. Otherwise, the temperature will cause excessive oxidation of the lubricating oil, leading to increased carbon deposits. This requires the lubricating oil in the cylinder to evaporate quickly and be carried away by the airflow to the cold zone of the compressor unit.
In the airflow, the movement process of the liquid fraction of the oil and its evaporation during this process are both affected by the viscosity of the oil. The higher the viscosity, the higher the evaporation temperature; in other words, the higher the viscosity, the longer the oil stays in the hot zone of the compressor unit, and the more carbon deposits will be formed.
Fire and explosion prevention measures for lubricating oil
A thorough solution to the safety problem of lubricating oil in compressors is to completely eliminate combustible substances in the system, i.e., using oil-free lubricated compressors. However, due to limitations in cost, service life, and operational reliability, using oil-free lubricated compressors is neither economical nor reasonable in some applications. In oil-lubricated compressors, solving the safety problem of lubricating oil requires finding other approaches.
For compressor units that use lubricating oil for cylinder lubrication, the measures to ensure safe operation are:
(1) Improve the physicochemical properties of the oil. Under the condition of ensuring normal friction and wear of the cylinder and piston assembly, lubricating oil with better thermal stability and lower viscosity should be used, even if the flash point is slightly lower.
During the refining process of lubricating oil, an appropriate amount of asphalt aromatic components should be ensured in the oil to prevent the oxidation of lubricating oil. Additives that prevent oxidation and carbon deposit precipitation can be added to the lubricating oil.
(2) Improve the working conditions of the oil. The operating temperature in the compressor cylinder should be reduced as much as possible to limit the area and time of high-temperature effects on the lubricating oil.
Using high-quality lubricating oil, and maintaining an operating temperature no higher than 150℃ or lower than the lubricating oil flash point by 28℃, can ensure safe operation of the compressor. However, limiting the cylinder temperature does not guarantee absolute safety, because even for the same compressor, local overheating may occur at normal temperatures. Under certain conditions, the oxidation reaction of oil carbon deposits after absorbing lubricating oil is an exothermic reaction. It itself becomes a heat source for temperature increase, and has no direct relationship with the temperature inside the cylinder. It is very important to avoid the accumulation of lubricating oil in the area where compressed air circulates. If carbon deposits and rust enter the lubricating oil, it will strongly hinder the circulation of the lubricating oil. Using stainless steel materials or coating the inner surface of the pipe with a special coating makes it difficult to form oil carbon deposits in the hot zone of the pipe.
Normal selection of lubricating oil consumption can greatly reduce oil carbon deposits. According to relevant information, if the lubricating oil consumption is reduced by half, the oil carbon deposits can be reduced to 1/20-1/30 of the original. Generally speaking, the cylinder lubricating oil consumption specified by the compressor manufacturer is too high, so the lubricating oil consumption can be determined through running tests in normal circumstances.
To reduce oil carbon deposits in the pipeline, the cooler should be installed as close to the cylinder as possible, and a high-efficiency oil-gas separator should be considered behind the compressor. In the compressed air pipeline system, structural defects that promote the accumulation of oil vapor or carbon deposits should be avoided, such as dead zones in containers, blind pipes, and sudden changes in pipe diameter.
(3) Removing oil carbon deposits. It is impossible to completely avoid oil oxidation and decomposition, so the aged lubricating oil and its decomposition products in the compressed air system should be removed regularly and timely. When the container is purged, in addition to purging the oil-water emulsion and compressed condensate, another function is to ventilate and purify the dead zone of the container.
China's "Safety Rules and Operating Procedures for Stationary Air Compressors" stipulates that any carbon deposits in oil-lubricated air compressors should be effectively removed regularly. For general power air compressors, the frequency of inspection and removal should be such that the carbon deposit layer thickness does not exceed 3mm.